below your new bottom slat . 11. Next, remove the rail plugs, untie the knot on the lift cords, and pull upward to release as many slats as you like. You now know how to shorten blinds and … Cut through one side of the pocket with scissors to craft length. Remove slats from the railhead. At this point, the middle pull cord should be loose. Photo 1 shows how to disassemble the cords … Page 4 of 11 Trim&Go! Page 3 of 9 Trim&Go! To shorten the length of the control cord, follow these steps: Look inside the headrail and find the vane carrier where the cord ends in a knot. Step 7. Next, slide the ladder plug back onto the lift cord and secure with a knot at the end of each cord. Wood Blind Shortening Instructions ... Cut the lift cord to remove the plugs; save the plugs for later . Trim The Ladder Cords: Double-check the desired length of the shortened window blind, and then trim the ladder cords after you’ve cut … There is way might work it start with chain connector, which joins the ends of the chain, than it can't able to pass through the gear. Enjoy Your Fitted Blinds. Lower the blinds to windowsill and make sure blinds are evenly level. Using scissors, carefully cut the knot off completely. To shorten the vertical blinds, you can follow the below steps. A flathead is ideal for this purpose. It keeps the blinds evenly level when adjusting because I always pull one cord more than the other. Raise your blind and … Tie a knot in the cord at that position. Mindy H. 222 STEPS. Test the blinds out by raising and lowering them, as well as opening and closing them a couple times to make sure all cords are secured and that the blinds are working correctly. Keep your scissors out and cut the cords on the venetian blinds at the marks you made earlier. Now that you’ve removed the covers, it’s time to locate the cord knot that holds the plug in place. Make sure that you do not cut the cords. Shorten Blind Pull Cords. Get rid of the weight from the pocket. Find the plugs covering each of the blind cords. After putting the cord knot in the hole, put the plug back on, which you removed earlier. To shorten your mini-blinds, start by placing them on a flat surface and expanding them to the full length. Step 8. Pop off the covers of the plugs with a screwdriver. Shorten Vertical Blinds. Find the back of the slat. And voila! Wood Blind Shortening Instructions Step 3: Select the slat even with (or slightly below) the window sill; this will be the new bottom slat Below the bottom slat, cut all the horizontal connector cords (repeat for all horizontal connector cords below the new bottom slat) NOTE: Be careful not to cut any vertical cords Most dangerous are the pull cords. Remove the paper clip from the pleat on which you will be cutting. With your scissors, cut the cords above the knots and remove the bottom of the blinds. Insert The Ladder Cords In The Bottom Rail: Insert the ladder cords in the opening in the bottom rail, and then pull them as far as possible. To leave enough room to tie the bottom rail back on, cut the string ladder connecter just below the rung that hangs below the bottom rail. How can I shorten my vertical blind control cord? You’ll be doing yourself a favor if you cut right above the slat below the mark you’ve made because it gives you more cord to play with. Just open it and drag the chain so the shade is fully up and do the same for it being fully down. Hold that vane carrier and pull out the excess cord until the cord safety device reaches the desired height. 10. Shortening the horizontal blinds to the proper height will raise the pull cords and make your home a safer place. Wood Blind Shortening Instructions Step 4: Slide the bottom rail out of the cords Cut all cords approx 6 in. Don’t worry about the excess cord. Set aside plastic buttons to be reattached after your cut. Cut the front of the pleat on the cellular shade, and then cut the back of the pleat. TOOLS. Unwrap the cords from the bottom of the blind and take off plastic buttons. The bottom rail runs through the ladder cords, and the pull cords are knotted below the rail on each end. This is a "knotting" technique that shortens w/o cutting. Step 4 - Cutting Cords.